CWE-CWE-667 CVE

CVE	Vendors	Products	Updated	CVSS v2	CVSS v3
CVE-2024-47746	1 Linux	1 Linux Kernel	2024-10-22	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: fuse: use exclusive lock when FUSE_I_CACHE_IO_MODE is set This may be a typo. The comment has said shared locks are not allowed when this bit is set. If using shared lock, the wait in `fuse_file_cached_io_open` may be forever.
CVE-2024-47744	1 Linux	1 Linux Kernel	2024-10-22	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: KVM: Use dedicated mutex to protect kvm_usage_count to avoid deadlock Use a dedicated mutex to guard kvm_usage_count to fix a potential deadlock on x86 due to a chain of locks and SRCU synchronizations. Translating the below lockdep splat, CPU1 #6 will wait on CPU0 #1, CPU0 #8 will wait on CPU2 #3, and CPU2 #7 will wait on CPU1 #4 (if there's a writer, due to the fairness of r/w semaphores). CPU0 CPU1 CPU2 1 lock(&kvm->slots_lock); 2 lock(&vcpu->mutex); 3 lock(&kvm->srcu); 4 lock(cpu_hotplug_lock); 5 lock(kvm_lock); 6 lock(&kvm->slots_lock); 7 lock(cpu_hotplug_lock); 8 sync(&kvm->srcu); Note, there are likely more potential deadlocks in KVM x86, e.g. the same pattern of taking cpu_hotplug_lock outside of kvm_lock likely exists with __kvmclock_cpufreq_notifier(): cpuhp_cpufreq_online() \| -> cpufreq_online() \| -> cpufreq_gov_performance_limits() \| -> __cpufreq_driver_target() \| -> __target_index() \| -> cpufreq_freq_transition_begin() \| -> cpufreq_notify_transition() \| -> ... __kvmclock_cpufreq_notifier() But, actually triggering such deadlocks is beyond rare due to the combination of dependencies and timings involved. E.g. the cpufreq notifier is only used on older CPUs without a constant TSC, mucking with the NX hugepage mitigation while VMs are running is very uncommon, and doing so while also onlining/offlining a CPU (necessary to generate contention on cpu_hotplug_lock) would be even more unusual. The most robust solution to the general cpu_hotplug_lock issue is likely to switch vm_list to be an RCU-protected list, e.g. so that x86's cpufreq notifier doesn't to take kvm_lock. For now, settle for fixing the most blatant deadlock, as switching to an RCU-protected list is a much more involved change, but add a comment in locking.rst to call out that care needs to be taken when walking holding kvm_lock and walking vm_list. ====================================================== WARNING: possible circular locking dependency detected 6.10.0-smp--c257535a0c9d-pip #330 Tainted: G S O ------------------------------------------------------ tee/35048 is trying to acquire lock: ff6a80eced71e0a8 (&kvm->slots_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x179/0x1e0 [kvm] but task is already holding lock: ffffffffc07abb08 (kvm_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x14a/0x1e0 [kvm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kvm_lock){+.+.}-{3:3}: __mutex_lock+0x6a/0xb40 mutex_lock_nested+0x1f/0x30 kvm_dev_ioctl+0x4fb/0xe50 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #2 (cpu_hotplug_lock){++++}-{0:0}: cpus_read_lock+0x2e/0xb0 static_key_slow_inc+0x16/0x30 kvm_lapic_set_base+0x6a/0x1c0 [kvm] kvm_set_apic_base+0x8f/0xe0 [kvm] kvm_set_msr_common+0x9ae/0xf80 [kvm] vmx_set_msr+0xa54/0xbe0 [kvm_intel] __kvm_set_msr+0xb6/0x1a0 [kvm] kvm_arch_vcpu_ioctl+0xeca/0x10c0 [kvm] kvm_vcpu_ioctl+0x485/0x5b0 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #1 (&kvm->srcu){.+.+}-{0:0}: __synchronize_srcu+0x44/0x1a0 ---truncated---
CVE-2024-44951	1 Linux	1 Linux Kernel	2024-10-09	N/A	7.8 HIGH
In the Linux kernel, the following vulnerability has been resolved: serial: sc16is7xx: fix TX fifo corruption Sometimes, when a packet is received on channel A at almost the same time as a packet is about to be transmitted on channel B, we observe with a logic analyzer that the received packet on channel A is transmitted on channel B. In other words, the Tx buffer data on channel B is corrupted with data from channel A. The problem appeared since commit 4409df5866b7 ("serial: sc16is7xx: change EFR lock to operate on each channels"), which changed the EFR locking to operate on each channel instead of chip-wise. This commit has introduced a regression, because the EFR lock is used not only to protect the EFR registers access, but also, in a very obscure and undocumented way, to protect access to the data buffer, which is shared by the Tx and Rx handlers, but also by each channel of the IC. Fix this regression first by switching to kfifo_out_linear_ptr() in sc16is7xx_handle_tx() to eliminate the need for a shared Rx/Tx buffer. Secondly, replace the chip-wise Rx buffer with a separate Rx buffer for each channel.
CVE-2024-46829	1 Linux	1 Linux Kernel	2024-10-02	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: rtmutex: Drop rt_mutex::wait_lock before scheduling rt_mutex_handle_deadlock() is called with rt_mutex::wait_lock held. In the good case it returns with the lock held and in the deadlock case it emits a warning and goes into an endless scheduling loop with the lock held, which triggers the 'scheduling in atomic' warning. Unlock rt_mutex::wait_lock in the dead lock case before issuing the warning and dropping into the schedule for ever loop. [ tglx: Moved unlock before the WARN(), removed the pointless comment, massaged changelog, added Fixes tag ]
CVE-2024-46867	1 Linux	1 Linux Kernel	2024-10-01	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: fix deadlock in show_meminfo() There is a real deadlock as well as sleeping in atomic() bug in here, if the bo put happens to be the last ref, since bo destruction wants to grab the same spinlock and sleeping locks. Fix that by dropping the ref using xe_bo_put_deferred(), and moving the final commit outside of the lock. Dropping the lock around the put is tricky since the bo can go out of scope and delete itself from the list, making it difficult to navigate to the next list entry. (cherry picked from commit 0083b8e6f11d7662283a267d4ce7c966812ffd8a)
CVE-2024-46866	1 Linux	1 Linux Kernel	2024-10-01	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: add missing bo locking in show_meminfo() bo_meminfo() wants to inspect bo state like tt and the ttm resource, however this state can change at any point leading to stuff like NPD and UAF, if the bo lock is not held. Grab the bo lock when calling bo_meminfo(), ensuring we drop any spinlocks first. In the case of object_idr we now also need to hold a ref. v2 (MattB) - Also add xe_bo_assert_held() (cherry picked from commit 4f63d712fa104c3ebefcb289d1e733e86d8698c7)
CVE-2024-46868	1 Linux	1 Linux Kernel	2024-10-01	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: uefisecapp: Fix deadlock in qcuefi_acquire() If the __qcuefi pointer is not set, then in the original code, we would hold onto the lock. That means that if we tried to set it later, then it would cause a deadlock. Drop the lock on the error path. That's what all the callers are expecting.
CVE-2024-46750	1 Linux	1 Linux Kernel	2024-09-30	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: PCI: Add missing bridge lock to pci_bus_lock() One of the true positives that the cfg_access_lock lockdep effort identified is this sequence: WARNING: CPU: 14 PID: 1 at drivers/pci/pci.c:4886 pci_bridge_secondary_bus_reset+0x5d/0x70 RIP: 0010:pci_bridge_secondary_bus_reset+0x5d/0x70 Call Trace: <TASK> ? __warn+0x8c/0x190 ? pci_bridge_secondary_bus_reset+0x5d/0x70 ? report_bug+0x1f8/0x200 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? pci_bridge_secondary_bus_reset+0x5d/0x70 pci_reset_bus+0x1d8/0x270 vmd_probe+0x778/0xa10 pci_device_probe+0x95/0x120 Where pci_reset_bus() users are triggering unlocked secondary bus resets. Ironically pci_bus_reset(), several calls down from pci_reset_bus(), uses pci_bus_lock() before issuing the reset which locks everything but the bridge itself. For the same motivation as adding: bridge = pci_upstream_bridge(dev); if (bridge) pci_dev_lock(bridge); to pci_reset_function() for the "bus" and "cxl_bus" reset cases, add pci_dev_lock() for @bus->self to pci_bus_lock(). [bhelgaas: squash in recursive locking deadlock fix from Keith Busch: https://lore.kernel.org/r/20240711193650.701834-1-kbusch@meta.com]
CVE-2024-46797	1 Linux	1 Linux Kernel	2024-09-29	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: powerpc/qspinlock: Fix deadlock in MCS queue If an interrupt occurs in queued_spin_lock_slowpath() after we increment qnodesp->count and before node->lock is initialized, another CPU might see stale lock values in get_tail_qnode(). If the stale lock value happens to match the lock on that CPU, then we write to the "next" pointer of the wrong qnode. This causes a deadlock as the former CPU, once it becomes the head of the MCS queue, will spin indefinitely until it's "next" pointer is set by its successor in the queue. Running stress-ng on a 16 core (16EC/16VP) shared LPAR, results in occasional lockups similar to the following: $ stress-ng --all 128 --vm-bytes 80% --aggressive \ --maximize --oomable --verify --syslog \ --metrics --times --timeout 5m watchdog: CPU 15 Hard LOCKUP ...... NIP [c0000000000b78f4] queued_spin_lock_slowpath+0x1184/0x1490 LR [c000000001037c5c] _raw_spin_lock+0x6c/0x90 Call Trace: 0xc000002cfffa3bf0 (unreliable) _raw_spin_lock+0x6c/0x90 raw_spin_rq_lock_nested.part.135+0x4c/0xd0 sched_ttwu_pending+0x60/0x1f0 __flush_smp_call_function_queue+0x1dc/0x670 smp_ipi_demux_relaxed+0xa4/0x100 xive_muxed_ipi_action+0x20/0x40 __handle_irq_event_percpu+0x80/0x240 handle_irq_event_percpu+0x2c/0x80 handle_percpu_irq+0x84/0xd0 generic_handle_irq+0x54/0x80 __do_irq+0xac/0x210 __do_IRQ+0x74/0xd0 0x0 do_IRQ+0x8c/0x170 hardware_interrupt_common_virt+0x29c/0x2a0 --- interrupt: 500 at queued_spin_lock_slowpath+0x4b8/0x1490 ...... NIP [c0000000000b6c28] queued_spin_lock_slowpath+0x4b8/0x1490 LR [c000000001037c5c] _raw_spin_lock+0x6c/0x90 --- interrupt: 500 0xc0000029c1a41d00 (unreliable) _raw_spin_lock+0x6c/0x90 futex_wake+0x100/0x260 do_futex+0x21c/0x2a0 sys_futex+0x98/0x270 system_call_exception+0x14c/0x2f0 system_call_vectored_common+0x15c/0x2ec The following code flow illustrates how the deadlock occurs. For the sake of brevity, assume that both locks (A and B) are contended and we call the queued_spin_lock_slowpath() function. CPU0 CPU1 ---- ---- spin_lock_irqsave(A) \| spin_unlock_irqrestore(A) \| spin_lock(B) \| \| \| ▼ \| id = qnodesp->count++; \| (Note that nodes[0].lock == A) \| \| \| ▼ \| Interrupt \| (happens before "nodes[0].lock = B") \| \| \| ▼ \| spin_lock_irqsave(A) \| \| \| ▼ \| id = qnodesp->count++ \| nodes[1].lock = A \| \| \| ▼ \| Tail of MCS queue \| \| spin_lock_irqsave(A) ▼ \| Head of MCS queue ▼ \| CPU0 is previous tail ▼ \| Spin indefinitely ▼ (until "nodes[1].next != NULL") prev = get_tail_qnode(A, CPU0) \| ▼ prev == &qnodes[CPU0].nodes[0] (as qnodes ---truncated---
CVE-2024-42114	1 Linux	1 Linux Kernel	2024-09-25	N/A	4.4 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values syzbot is able to trigger softlockups, setting NL80211_ATTR_TXQ_QUANTUM to 2^31. We had a similar issue in sch_fq, fixed with commit d9e15a273306 ("pkt_sched: fq: do not accept silly TCA_FQ_QUANTUM") watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [kworker/1:0:24] Modules linked in: irq event stamp: 131135 hardirqs last enabled at (131134): [<ffff80008ae8778c>] __exit_to_kernel_mode arch/arm64/kernel/entry-common.c:85 [inline] hardirqs last enabled at (131134): [<ffff80008ae8778c>] exit_to_kernel_mode+0xdc/0x10c arch/arm64/kernel/entry-common.c:95 hardirqs last disabled at (131135): [<ffff80008ae85378>] __el1_irq arch/arm64/kernel/entry-common.c:533 [inline] hardirqs last disabled at (131135): [<ffff80008ae85378>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:551 softirqs last enabled at (125892): [<ffff80008907e82c>] neigh_hh_init net/core/neighbour.c:1538 [inline] softirqs last enabled at (125892): [<ffff80008907e82c>] neigh_resolve_output+0x268/0x658 net/core/neighbour.c:1553 softirqs last disabled at (125896): [<ffff80008904166c>] local_bh_disable+0x10/0x34 include/linux/bottom_half.h:19 CPU: 1 PID: 24 Comm: kworker/1:0 Not tainted 6.9.0-rc7-syzkaller-gfda5695d692c #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Workqueue: mld mld_ifc_work pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __list_del include/linux/list.h:195 [inline] pc : __list_del_entry include/linux/list.h:218 [inline] pc : list_move_tail include/linux/list.h:310 [inline] pc : fq_tin_dequeue include/net/fq_impl.h:112 [inline] pc : ieee80211_tx_dequeue+0x6b8/0x3b4c net/mac80211/tx.c:3854 lr : __list_del_entry include/linux/list.h:218 [inline] lr : list_move_tail include/linux/list.h:310 [inline] lr : fq_tin_dequeue include/net/fq_impl.h:112 [inline] lr : ieee80211_tx_dequeue+0x67c/0x3b4c net/mac80211/tx.c:3854 sp : ffff800093d36700 x29: ffff800093d36a60 x28: ffff800093d36960 x27: dfff800000000000 x26: ffff0000d800ad50 x25: ffff0000d800abe0 x24: ffff0000d800abf0 x23: ffff0000e0032468 x22: ffff0000e00324d4 x21: ffff0000d800abf0 x20: ffff0000d800abf8 x19: ffff0000d800abf0 x18: ffff800093d363c0 x17: 000000000000d476 x16: ffff8000805519dc x15: ffff7000127a6cc8 x14: 1ffff000127a6cc8 x13: 0000000000000004 x12: ffffffffffffffff x11: ffff7000127a6cc8 x10: 0000000000ff0100 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : ffff80009287aa08 x4 : 0000000000000008 x3 : ffff80008034c7fc x2 : ffff0000e0032468 x1 : 00000000da0e46b8 x0 : ffff0000e0032470 Call trace: __list_del include/linux/list.h:195 [inline] __list_del_entry include/linux/list.h:218 [inline] list_move_tail include/linux/list.h:310 [inline] fq_tin_dequeue include/net/fq_impl.h:112 [inline] ieee80211_tx_dequeue+0x6b8/0x3b4c net/mac80211/tx.c:3854 wake_tx_push_queue net/mac80211/util.c:294 [inline] ieee80211_handle_wake_tx_queue+0x118/0x274 net/mac80211/util.c:315 drv_wake_tx_queue net/mac80211/driver-ops.h:1350 [inline] schedule_and_wake_txq net/mac80211/driver-ops.h:1357 [inline] ieee80211_queue_skb+0x18e8/0x2244 net/mac80211/tx.c:1664 ieee80211_tx+0x260/0x400 net/mac80211/tx.c:1966 ieee80211_xmit+0x278/0x354 net/mac80211/tx.c:2062 __ieee80211_subif_start_xmit+0xab8/0x122c net/mac80211/tx.c:4338 ieee80211_subif_start_xmit+0xe0/0x438 net/mac80211/tx.c:4532 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x27c/0x938 net/core/dev.c:3547 __dev_queue_xmit+0x1678/0x33fc net/core/dev.c:4341 dev_queue_xmit include/linux/netdevice.h:3091 [inline] neigh_resolve_output+0x558/0x658 net/core/neighbour.c:1563 neigh_output include/net/neighbour.h:542 [inline] ip6_fini ---truncated---
CVE-2024-46678	1 Linux	1 Linux Kernel	2024-09-23	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: bonding: change ipsec_lock from spin lock to mutex In the cited commit, bond->ipsec_lock is added to protect ipsec_list, hence xdo_dev_state_add and xdo_dev_state_delete are called inside this lock. As ipsec_lock is a spin lock and such xfrmdev ops may sleep, "scheduling while atomic" will be triggered when changing bond's active slave. [ 101.055189] BUG: scheduling while atomic: bash/902/0x00000200 [ 101.055726] Modules linked in: [ 101.058211] CPU: 3 PID: 902 Comm: bash Not tainted 6.9.0-rc4+ #1 [ 101.058760] Hardware name: [ 101.059434] Call Trace: [ 101.059436] <TASK> [ 101.060873] dump_stack_lvl+0x51/0x60 [ 101.061275] __schedule_bug+0x4e/0x60 [ 101.061682] __schedule+0x612/0x7c0 [ 101.062078] ? __mod_timer+0x25c/0x370 [ 101.062486] schedule+0x25/0xd0 [ 101.062845] schedule_timeout+0x77/0xf0 [ 101.063265] ? asm_common_interrupt+0x22/0x40 [ 101.063724] ? __bpf_trace_itimer_state+0x10/0x10 [ 101.064215] __wait_for_common+0x87/0x190 [ 101.064648] ? usleep_range_state+0x90/0x90 [ 101.065091] cmd_exec+0x437/0xb20 [mlx5_core] [ 101.065569] mlx5_cmd_do+0x1e/0x40 [mlx5_core] [ 101.066051] mlx5_cmd_exec+0x18/0x30 [mlx5_core] [ 101.066552] mlx5_crypto_create_dek_key+0xea/0x120 [mlx5_core] [ 101.067163] ? bonding_sysfs_store_option+0x4d/0x80 [bonding] [ 101.067738] ? kmalloc_trace+0x4d/0x350 [ 101.068156] mlx5_ipsec_create_sa_ctx+0x33/0x100 [mlx5_core] [ 101.068747] mlx5e_xfrm_add_state+0x47b/0xaa0 [mlx5_core] [ 101.069312] bond_change_active_slave+0x392/0x900 [bonding] [ 101.069868] bond_option_active_slave_set+0x1c2/0x240 [bonding] [ 101.070454] __bond_opt_set+0xa6/0x430 [bonding] [ 101.070935] __bond_opt_set_notify+0x2f/0x90 [bonding] [ 101.071453] bond_opt_tryset_rtnl+0x72/0xb0 [bonding] [ 101.071965] bonding_sysfs_store_option+0x4d/0x80 [bonding] [ 101.072567] kernfs_fop_write_iter+0x10c/0x1a0 [ 101.073033] vfs_write+0x2d8/0x400 [ 101.073416] ? alloc_fd+0x48/0x180 [ 101.073798] ksys_write+0x5f/0xe0 [ 101.074175] do_syscall_64+0x52/0x110 [ 101.074576] entry_SYSCALL_64_after_hwframe+0x4b/0x53 As bond_ipsec_add_sa_all and bond_ipsec_del_sa_all are only called from bond_change_active_slave, which requires holding the RTNL lock. And bond_ipsec_add_sa and bond_ipsec_del_sa are xfrm state xdo_dev_state_add and xdo_dev_state_delete APIs, which are in user context. So ipsec_lock doesn't have to be spin lock, change it to mutex, and thus the above issue can be resolved.
CVE-2024-46791	1 Linux	1 Linux Kernel	2024-09-20	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open The mcp251x_hw_wake() function is called with the mpc_lock mutex held and disables the interrupt handler so that no interrupts can be processed while waking the device. If an interrupt has already occurred then waiting for the interrupt handler to complete will deadlock because it will be trying to acquire the same mutex. CPU0 CPU1 ---- ---- mcp251x_open() mutex_lock(&priv->mcp_lock) request_threaded_irq() <interrupt> mcp251x_can_ist() mutex_lock(&priv->mcp_lock) mcp251x_hw_wake() disable_irq() <-- deadlock Use disable_irq_nosync() instead because the interrupt handler does everything while holding the mutex so it doesn't matter if it's still running.
CVE-2022-48719	1 Linux	1 Linux Kernel	2024-09-18	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: net, neigh: Do not trigger immediate probes on NUD_FAILED from neigh_managed_work syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]: kworker/0:16/14617 is trying to acquire lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 [...] but task is already holding lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572 The neighbor entry turned to NUD_FAILED state, where __neigh_event_send() triggered an immediate probe as per commit cd28ca0a3dd1 ("neigh: reduce arp latency") via neigh_probe() given table lock was held. One option to fix this situation is to defer the neigh_probe() back to the neigh_timer_handler() similarly as pre cd28ca0a3dd1. For the case of NTF_MANAGED, this deferral is acceptable given this only happens on actual failure state and regular / expected state is NUD_VALID with the entry already present. The fix adds a parameter to __neigh_event_send() in order to communicate whether immediate probe is allowed or disallowed. Existing call-sites of neigh_event_send() default as-is to immediate probe. However, the neigh_managed_work() disables it via use of neigh_event_send_probe(). [0] <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_deadlock_bug kernel/locking/lockdep.c:2956 [inline] check_deadlock kernel/locking/lockdep.c:2999 [inline] validate_chain kernel/locking/lockdep.c:3788 [inline] __lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027 lock_acquire kernel/locking/lockdep.c:5639 [inline] lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604 __raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline] _raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334 ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline] __ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170 ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201 NF_HOOK_COND include/linux/netfilter.h:296 [inline] ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224 dst_output include/net/dst.h:451 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508 ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650 ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742 neigh_probe+0xc2/0x110 net/core/neighbour.c:1040 __neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201 neigh_event_send include/net/neighbour.h:470 [inline] neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574 process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307 worker_thread+0x657/0x1110 kernel/workqueue.c:2454 kthread+0x2e9/0x3a0 kernel/kthread.c:377 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 </TASK>
CVE-2024-44995	1 Linux	1 Linux Kernel	2024-09-15	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix a deadlock problem when config TC during resetting When config TC during the reset process, may cause a deadlock, the flow is as below: pf reset start │ ▼ ...... setup tc │ │ ▼ ▼ DOWN: napi_disable() napi_disable()(skip) │ │ │ ▼ ▼ ...... ...... │ │ ▼ │ napi_enable() │ ▼ UINIT: netif_napi_del() │ ▼ ...... │ ▼ INIT: netif_napi_add() │ ▼ ...... global reset start │ │ ▼ ▼ UP: napi_enable()(skip) ...... │ │ ▼ ▼ ...... napi_disable() In reset process, the driver will DOWN the port and then UINIT, in this case, the setup tc process will UP the port before UINIT, so cause the problem. Adds a DOWN process in UINIT to fix it.
CVE-2023-3750	1 Redhat	2 Enterprise Linux, Libvirt	2024-09-13	N/A	5.3 MEDIUM
A flaw was found in libvirt. The virStoragePoolObjListSearch function does not return a locked pool as expected, resulting in a race condition and denial of service when attempting to lock the same object from another thread. This issue could allow clients connecting to the read-only socket to crash the libvirt daemon.
CVE-2021-22530	1 Microfocus	1 Netiq Advanced Authentication	2024-09-13	N/A	9.9 CRITICAL
A vulnerability identified in NetIQ Advance Authentication that doesn't enforce account lockout when brute force attack is performed on API based login. This issue may lead to user account compromise if successful or may impact server performance. This issue impacts all NetIQ Advance Authentication before 6.3.5.1
CVE-2024-46692	1 Linux	1 Linux Kernel	2024-09-13	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: scm: Mark get_wq_ctx() as atomic call Currently get_wq_ctx() is wrongly configured as a standard call. When two SMC calls are in sleep and one SMC wakes up, it calls get_wq_ctx() to resume the corresponding sleeping thread. But if get_wq_ctx() is interrupted, goes to sleep and another SMC call is waiting to be allocated a waitq context, it leads to a deadlock. To avoid this get_wq_ctx() must be an atomic call and can't be a standard SMC call. Hence mark get_wq_ctx() as a fast call.
CVE-2024-45019	1 Linux	1 Linux Kernel	2024-09-13	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Take state lock during tx timeout reporter mlx5e_safe_reopen_channels() requires the state lock taken. The referenced changed in the Fixes tag removed the lock to fix another issue. This patch adds it back but at a later point (when calling mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the Fixes tag.
CVE-2024-45024	1 Linux	1 Linux Kernel	2024-09-13	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: mm/hugetlb: fix hugetlb vs. core-mm PT locking We recently made GUP's common page table walking code to also walk hugetlb VMAs without most hugetlb special-casing, preparing for the future of having less hugetlb-specific page table walking code in the codebase. Turns out that we missed one page table locking detail: page table locking for hugetlb folios that are not mapped using a single PMD/PUD. Assume we have hugetlb folio that spans multiple PTEs (e.g., 64 KiB hugetlb folios on arm64 with 4 KiB base page size). GUP, as it walks the page tables, will perform a pte_offset_map_lock() to grab the PTE table lock. However, hugetlb that concurrently modifies these page tables would actually grab the mm->page_table_lock: with USE_SPLIT_PTE_PTLOCKS, the locks would differ. Something similar can happen right now with hugetlb folios that span multiple PMDs when USE_SPLIT_PMD_PTLOCKS. This issue can be reproduced [1], for example triggering: [ 3105.936100] ------------[ cut here ]------------ [ 3105.939323] WARNING: CPU: 31 PID: 2732 at mm/gup.c:142 try_grab_folio+0x11c/0x188 [ 3105.944634] Modules linked in: [...] [ 3105.974841] CPU: 31 PID: 2732 Comm: reproducer Not tainted 6.10.0-64.eln141.aarch64 #1 [ 3105.980406] Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20240524-4.fc40 05/24/2024 [ 3105.986185] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 3105.991108] pc : try_grab_folio+0x11c/0x188 [ 3105.994013] lr : follow_page_pte+0xd8/0x430 [ 3105.996986] sp : ffff80008eafb8f0 [ 3105.999346] x29: ffff80008eafb900 x28: ffffffe8d481f380 x27: 00f80001207cff43 [ 3106.004414] x26: 0000000000000001 x25: 0000000000000000 x24: ffff80008eafba48 [ 3106.009520] x23: 0000ffff9372f000 x22: ffff7a54459e2000 x21: ffff7a546c1aa978 [ 3106.014529] x20: ffffffe8d481f3c0 x19: 0000000000610041 x18: 0000000000000001 [ 3106.019506] x17: 0000000000000001 x16: ffffffffffffffff x15: 0000000000000000 [ 3106.024494] x14: ffffb85477fdfe08 x13: 0000ffff9372ffff x12: 0000000000000000 [ 3106.029469] x11: 1fffef4a88a96be1 x10: ffff7a54454b5f0c x9 : ffffb854771b12f0 [ 3106.034324] x8 : 0008000000000000 x7 : ffff7a546c1aa980 x6 : 0008000000000080 [ 3106.038902] x5 : 00000000001207cf x4 : 0000ffff9372f000 x3 : ffffffe8d481f000 [ 3106.043420] x2 : 0000000000610041 x1 : 0000000000000001 x0 : 0000000000000000 [ 3106.047957] Call trace: [ 3106.049522] try_grab_folio+0x11c/0x188 [ 3106.051996] follow_pmd_mask.constprop.0.isra.0+0x150/0x2e0 [ 3106.055527] follow_page_mask+0x1a0/0x2b8 [ 3106.058118] __get_user_pages+0xf0/0x348 [ 3106.060647] faultin_page_range+0xb0/0x360 [ 3106.063651] do_madvise+0x340/0x598 Let's make huge_pte_lockptr() effectively use the same PT locks as any core-mm page table walker would. Add ptep_lockptr() to obtain the PTE page table lock using a pte pointer -- unfortunately we cannot convert pte_lockptr() because virt_to_page() doesn't work with kmap'ed page tables we can have with CONFIG_HIGHPTE. Handle CONFIG_PGTABLE_LEVELS correctly by checking in reverse order, such that when e.g., CONFIG_PGTABLE_LEVELS==2 with PGDIR_SIZE==P4D_SIZE==PUD_SIZE==PMD_SIZE will work as expected. Document why that works. There is one ugly case: powerpc 8xx, whereby we have an 8 MiB hugetlb folio being mapped using two PTE page tables. While hugetlb wants to take the PMD table lock, core-mm would grab the PTE table lock of one of both PTE page tables. In such corner cases, we have to make sure that both locks match, which is (fortunately!) currently guaranteed for 8xx as it does not support SMP and consequently doesn't use split PT locks. [1] https://lore.kernel.org/all/1bbfcc7f-f222-45a5-ac44-c5a1381c596d@redhat.com/
CVE-2024-45029	1 Linux	1 Linux Kernel	2024-09-13	N/A	5.5 MEDIUM
In the Linux kernel, the following vulnerability has been resolved: i2c: tegra: Do not mark ACPI devices as irq safe On ACPI machines, the tegra i2c module encounters an issue due to a mutex being called inside a spinlock. This leads to the following bug: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585 ... Call trace: __might_sleep __mutex_lock_common mutex_lock_nested acpi_subsys_runtime_resume rpm_resume tegra_i2c_xfer The problem arises because during __pm_runtime_resume(), the spinlock &dev->power.lock is acquired before rpm_resume() is called. Later, rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on mutexes, triggering the error. To address this issue, devices on ACPI are now marked as not IRQ-safe, considering the dependency of acpi_subsys_runtime_resume() on mutexes.

In the Linux kernel, the following vulnerability has been resolved: fuse: use exclusive lock when FUSE_I_CACHE_IO_MODE is set This may be a typo. The comment has said shared locks are not allowed when this bit is set. If using shared lock, the wait in `fuse_file_cached_io_open` may be forever.

In the Linux kernel, the following vulnerability has been resolved: KVM: Use dedicated mutex to protect kvm_usage_count to avoid deadlock Use a dedicated mutex to guard kvm_usage_count to fix a potential deadlock on x86 due to a chain of locks and SRCU synchronizations. Translating the below lockdep splat, CPU1 #6 will wait on CPU0 #1, CPU0 #8 will wait on CPU2 #3, and CPU2 #7 will wait on CPU1 #4 (if there's a writer, due to the fairness of r/w semaphores). CPU0 CPU1 CPU2 1 lock(&kvm->slots_lock); 2 lock(&vcpu->mutex); 3 lock(&kvm->srcu); 4 lock(cpu_hotplug_lock); 5 lock(kvm_lock); 6 lock(&kvm->slots_lock); 7 lock(cpu_hotplug_lock); 8 sync(&kvm->srcu); Note, there are likely more potential deadlocks in KVM x86, e.g. the same pattern of taking cpu_hotplug_lock outside of kvm_lock likely exists with __kvmclock_cpufreq_notifier(): cpuhp_cpufreq_online() | -> cpufreq_online() | -> cpufreq_gov_performance_limits() | -> __cpufreq_driver_target() | -> __target_index() | -> cpufreq_freq_transition_begin() | -> cpufreq_notify_transition() | -> ... __kvmclock_cpufreq_notifier() But, actually triggering such deadlocks is beyond rare due to the combination of dependencies and timings involved. E.g. the cpufreq notifier is only used on older CPUs without a constant TSC, mucking with the NX hugepage mitigation while VMs are running is very uncommon, and doing so while also onlining/offlining a CPU (necessary to generate contention on cpu_hotplug_lock) would be even more unusual. The most robust solution to the general cpu_hotplug_lock issue is likely to switch vm_list to be an RCU-protected list, e.g. so that x86's cpufreq notifier doesn't to take kvm_lock. For now, settle for fixing the most blatant deadlock, as switching to an RCU-protected list is a much more involved change, but add a comment in locking.rst to call out that care needs to be taken when walking holding kvm_lock and walking vm_list. ====================================================== WARNING: possible circular locking dependency detected 6.10.0-smp--c257535a0c9d-pip #330 Tainted: G S O ------------------------------------------------------ tee/35048 is trying to acquire lock: ff6a80eced71e0a8 (&kvm->slots_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x179/0x1e0 [kvm] but task is already holding lock: ffffffffc07abb08 (kvm_lock){+.+.}-{3:3}, at: set_nx_huge_pages+0x14a/0x1e0 [kvm] which lock already depends on the new lock. the existing dependency chain (in reverse order) is: -> #3 (kvm_lock){+.+.}-{3:3}: __mutex_lock+0x6a/0xb40 mutex_lock_nested+0x1f/0x30 kvm_dev_ioctl+0x4fb/0xe50 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #2 (cpu_hotplug_lock){++++}-{0:0}: cpus_read_lock+0x2e/0xb0 static_key_slow_inc+0x16/0x30 kvm_lapic_set_base+0x6a/0x1c0 [kvm] kvm_set_apic_base+0x8f/0xe0 [kvm] kvm_set_msr_common+0x9ae/0xf80 [kvm] vmx_set_msr+0xa54/0xbe0 [kvm_intel] __kvm_set_msr+0xb6/0x1a0 [kvm] kvm_arch_vcpu_ioctl+0xeca/0x10c0 [kvm] kvm_vcpu_ioctl+0x485/0x5b0 [kvm] __se_sys_ioctl+0x7b/0xd0 __x64_sys_ioctl+0x21/0x30 x64_sys_call+0x15d0/0x2e60 do_syscall_64+0x83/0x160 entry_SYSCALL_64_after_hwframe+0x76/0x7e -> #1 (&kvm->srcu){.+.+}-{0:0}: __synchronize_srcu+0x44/0x1a0 ---truncated---

In the Linux kernel, the following vulnerability has been resolved: serial: sc16is7xx: fix TX fifo corruption Sometimes, when a packet is received on channel A at almost the same time as a packet is about to be transmitted on channel B, we observe with a logic analyzer that the received packet on channel A is transmitted on channel B. In other words, the Tx buffer data on channel B is corrupted with data from channel A. The problem appeared since commit 4409df5866b7 ("serial: sc16is7xx: change EFR lock to operate on each channels"), which changed the EFR locking to operate on each channel instead of chip-wise. This commit has introduced a regression, because the EFR lock is used not only to protect the EFR registers access, but also, in a very obscure and undocumented way, to protect access to the data buffer, which is shared by the Tx and Rx handlers, but also by each channel of the IC. Fix this regression first by switching to kfifo_out_linear_ptr() in sc16is7xx_handle_tx() to eliminate the need for a shared Rx/Tx buffer. Secondly, replace the chip-wise Rx buffer with a separate Rx buffer for each channel.

In the Linux kernel, the following vulnerability has been resolved: rtmutex: Drop rt_mutex::wait_lock before scheduling rt_mutex_handle_deadlock() is called with rt_mutex::wait_lock held. In the good case it returns with the lock held and in the deadlock case it emits a warning and goes into an endless scheduling loop with the lock held, which triggers the 'scheduling in atomic' warning. Unlock rt_mutex::wait_lock in the dead lock case before issuing the warning and dropping into the schedule for ever loop. [ tglx: Moved unlock before the WARN(), removed the pointless comment, massaged changelog, added Fixes tag ]

In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: fix deadlock in show_meminfo() There is a real deadlock as well as sleeping in atomic() bug in here, if the bo put happens to be the last ref, since bo destruction wants to grab the same spinlock and sleeping locks. Fix that by dropping the ref using xe_bo_put_deferred(), and moving the final commit outside of the lock. Dropping the lock around the put is tricky since the bo can go out of scope and delete itself from the list, making it difficult to navigate to the next list entry. (cherry picked from commit 0083b8e6f11d7662283a267d4ce7c966812ffd8a)

In the Linux kernel, the following vulnerability has been resolved: drm/xe/client: add missing bo locking in show_meminfo() bo_meminfo() wants to inspect bo state like tt and the ttm resource, however this state can change at any point leading to stuff like NPD and UAF, if the bo lock is not held. Grab the bo lock when calling bo_meminfo(), ensuring we drop any spinlocks first. In the case of object_idr we now also need to hold a ref. v2 (MattB) - Also add xe_bo_assert_held() (cherry picked from commit 4f63d712fa104c3ebefcb289d1e733e86d8698c7)

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: uefisecapp: Fix deadlock in qcuefi_acquire() If the __qcuefi pointer is not set, then in the original code, we would hold onto the lock. That means that if we tried to set it later, then it would cause a deadlock. Drop the lock on the error path. That's what all the callers are expecting.

In the Linux kernel, the following vulnerability has been resolved: PCI: Add missing bridge lock to pci_bus_lock() One of the true positives that the cfg_access_lock lockdep effort identified is this sequence: WARNING: CPU: 14 PID: 1 at drivers/pci/pci.c:4886 pci_bridge_secondary_bus_reset+0x5d/0x70 RIP: 0010:pci_bridge_secondary_bus_reset+0x5d/0x70 Call Trace: <TASK> ? __warn+0x8c/0x190 ? pci_bridge_secondary_bus_reset+0x5d/0x70 ? report_bug+0x1f8/0x200 ? handle_bug+0x3c/0x70 ? exc_invalid_op+0x18/0x70 ? asm_exc_invalid_op+0x1a/0x20 ? pci_bridge_secondary_bus_reset+0x5d/0x70 pci_reset_bus+0x1d8/0x270 vmd_probe+0x778/0xa10 pci_device_probe+0x95/0x120 Where pci_reset_bus() users are triggering unlocked secondary bus resets. Ironically pci_bus_reset(), several calls down from pci_reset_bus(), uses pci_bus_lock() before issuing the reset which locks everything *but* the bridge itself. For the same motivation as adding: bridge = pci_upstream_bridge(dev); if (bridge) pci_dev_lock(bridge); to pci_reset_function() for the "bus" and "cxl_bus" reset cases, add pci_dev_lock() for @bus->self to pci_bus_lock(). [bhelgaas: squash in recursive locking deadlock fix from Keith Busch: https://lore.kernel.org/r/20240711193650.701834-1-kbusch@meta.com]

In the Linux kernel, the following vulnerability has been resolved: powerpc/qspinlock: Fix deadlock in MCS queue If an interrupt occurs in queued_spin_lock_slowpath() after we increment qnodesp->count and before node->lock is initialized, another CPU might see stale lock values in get_tail_qnode(). If the stale lock value happens to match the lock on that CPU, then we write to the "next" pointer of the wrong qnode. This causes a deadlock as the former CPU, once it becomes the head of the MCS queue, will spin indefinitely until it's "next" pointer is set by its successor in the queue. Running stress-ng on a 16 core (16EC/16VP) shared LPAR, results in occasional lockups similar to the following: $ stress-ng --all 128 --vm-bytes 80% --aggressive \ --maximize --oomable --verify --syslog \ --metrics --times --timeout 5m watchdog: CPU 15 Hard LOCKUP ...... NIP [c0000000000b78f4] queued_spin_lock_slowpath+0x1184/0x1490 LR [c000000001037c5c] _raw_spin_lock+0x6c/0x90 Call Trace: 0xc000002cfffa3bf0 (unreliable) _raw_spin_lock+0x6c/0x90 raw_spin_rq_lock_nested.part.135+0x4c/0xd0 sched_ttwu_pending+0x60/0x1f0 __flush_smp_call_function_queue+0x1dc/0x670 smp_ipi_demux_relaxed+0xa4/0x100 xive_muxed_ipi_action+0x20/0x40 __handle_irq_event_percpu+0x80/0x240 handle_irq_event_percpu+0x2c/0x80 handle_percpu_irq+0x84/0xd0 generic_handle_irq+0x54/0x80 __do_irq+0xac/0x210 __do_IRQ+0x74/0xd0 0x0 do_IRQ+0x8c/0x170 hardware_interrupt_common_virt+0x29c/0x2a0 --- interrupt: 500 at queued_spin_lock_slowpath+0x4b8/0x1490 ...... NIP [c0000000000b6c28] queued_spin_lock_slowpath+0x4b8/0x1490 LR [c000000001037c5c] _raw_spin_lock+0x6c/0x90 --- interrupt: 500 0xc0000029c1a41d00 (unreliable) _raw_spin_lock+0x6c/0x90 futex_wake+0x100/0x260 do_futex+0x21c/0x2a0 sys_futex+0x98/0x270 system_call_exception+0x14c/0x2f0 system_call_vectored_common+0x15c/0x2ec The following code flow illustrates how the deadlock occurs. For the sake of brevity, assume that both locks (A and B) are contended and we call the queued_spin_lock_slowpath() function. CPU0 CPU1 ---- ---- spin_lock_irqsave(A) | spin_unlock_irqrestore(A) | spin_lock(B) | | | ▼ | id = qnodesp->count++; | (Note that nodes[0].lock == A) | | | ▼ | Interrupt | (happens before "nodes[0].lock = B") | | | ▼ | spin_lock_irqsave(A) | | | ▼ | id = qnodesp->count++ | nodes[1].lock = A | | | ▼ | Tail of MCS queue | | spin_lock_irqsave(A) ▼ | Head of MCS queue ▼ | CPU0 is previous tail ▼ | Spin indefinitely ▼ (until "nodes[1].next != NULL") prev = get_tail_qnode(A, CPU0) | ▼ prev == &qnodes[CPU0].nodes[0] (as qnodes ---truncated---

In the Linux kernel, the following vulnerability has been resolved: wifi: cfg80211: restrict NL80211_ATTR_TXQ_QUANTUM values syzbot is able to trigger softlockups, setting NL80211_ATTR_TXQ_QUANTUM to 2^31. We had a similar issue in sch_fq, fixed with commit d9e15a273306 ("pkt_sched: fq: do not accept silly TCA_FQ_QUANTUM") watchdog: BUG: soft lockup - CPU#1 stuck for 26s! [kworker/1:0:24] Modules linked in: irq event stamp: 131135 hardirqs last enabled at (131134): [<ffff80008ae8778c>] __exit_to_kernel_mode arch/arm64/kernel/entry-common.c:85 [inline] hardirqs last enabled at (131134): [<ffff80008ae8778c>] exit_to_kernel_mode+0xdc/0x10c arch/arm64/kernel/entry-common.c:95 hardirqs last disabled at (131135): [<ffff80008ae85378>] __el1_irq arch/arm64/kernel/entry-common.c:533 [inline] hardirqs last disabled at (131135): [<ffff80008ae85378>] el1_interrupt+0x24/0x68 arch/arm64/kernel/entry-common.c:551 softirqs last enabled at (125892): [<ffff80008907e82c>] neigh_hh_init net/core/neighbour.c:1538 [inline] softirqs last enabled at (125892): [<ffff80008907e82c>] neigh_resolve_output+0x268/0x658 net/core/neighbour.c:1553 softirqs last disabled at (125896): [<ffff80008904166c>] local_bh_disable+0x10/0x34 include/linux/bottom_half.h:19 CPU: 1 PID: 24 Comm: kworker/1:0 Not tainted 6.9.0-rc7-syzkaller-gfda5695d692c #0 Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 03/27/2024 Workqueue: mld mld_ifc_work pstate: 80400005 (Nzcv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--) pc : __list_del include/linux/list.h:195 [inline] pc : __list_del_entry include/linux/list.h:218 [inline] pc : list_move_tail include/linux/list.h:310 [inline] pc : fq_tin_dequeue include/net/fq_impl.h:112 [inline] pc : ieee80211_tx_dequeue+0x6b8/0x3b4c net/mac80211/tx.c:3854 lr : __list_del_entry include/linux/list.h:218 [inline] lr : list_move_tail include/linux/list.h:310 [inline] lr : fq_tin_dequeue include/net/fq_impl.h:112 [inline] lr : ieee80211_tx_dequeue+0x67c/0x3b4c net/mac80211/tx.c:3854 sp : ffff800093d36700 x29: ffff800093d36a60 x28: ffff800093d36960 x27: dfff800000000000 x26: ffff0000d800ad50 x25: ffff0000d800abe0 x24: ffff0000d800abf0 x23: ffff0000e0032468 x22: ffff0000e00324d4 x21: ffff0000d800abf0 x20: ffff0000d800abf8 x19: ffff0000d800abf0 x18: ffff800093d363c0 x17: 000000000000d476 x16: ffff8000805519dc x15: ffff7000127a6cc8 x14: 1ffff000127a6cc8 x13: 0000000000000004 x12: ffffffffffffffff x11: ffff7000127a6cc8 x10: 0000000000ff0100 x9 : 0000000000000000 x8 : 0000000000000000 x7 : 0000000000000000 x6 : 0000000000000000 x5 : ffff80009287aa08 x4 : 0000000000000008 x3 : ffff80008034c7fc x2 : ffff0000e0032468 x1 : 00000000da0e46b8 x0 : ffff0000e0032470 Call trace: __list_del include/linux/list.h:195 [inline] __list_del_entry include/linux/list.h:218 [inline] list_move_tail include/linux/list.h:310 [inline] fq_tin_dequeue include/net/fq_impl.h:112 [inline] ieee80211_tx_dequeue+0x6b8/0x3b4c net/mac80211/tx.c:3854 wake_tx_push_queue net/mac80211/util.c:294 [inline] ieee80211_handle_wake_tx_queue+0x118/0x274 net/mac80211/util.c:315 drv_wake_tx_queue net/mac80211/driver-ops.h:1350 [inline] schedule_and_wake_txq net/mac80211/driver-ops.h:1357 [inline] ieee80211_queue_skb+0x18e8/0x2244 net/mac80211/tx.c:1664 ieee80211_tx+0x260/0x400 net/mac80211/tx.c:1966 ieee80211_xmit+0x278/0x354 net/mac80211/tx.c:2062 __ieee80211_subif_start_xmit+0xab8/0x122c net/mac80211/tx.c:4338 ieee80211_subif_start_xmit+0xe0/0x438 net/mac80211/tx.c:4532 __netdev_start_xmit include/linux/netdevice.h:4903 [inline] netdev_start_xmit include/linux/netdevice.h:4917 [inline] xmit_one net/core/dev.c:3531 [inline] dev_hard_start_xmit+0x27c/0x938 net/core/dev.c:3547 __dev_queue_xmit+0x1678/0x33fc net/core/dev.c:4341 dev_queue_xmit include/linux/netdevice.h:3091 [inline] neigh_resolve_output+0x558/0x658 net/core/neighbour.c:1563 neigh_output include/net/neighbour.h:542 [inline] ip6_fini ---truncated---

In the Linux kernel, the following vulnerability has been resolved: bonding: change ipsec_lock from spin lock to mutex In the cited commit, bond->ipsec_lock is added to protect ipsec_list, hence xdo_dev_state_add and xdo_dev_state_delete are called inside this lock. As ipsec_lock is a spin lock and such xfrmdev ops may sleep, "scheduling while atomic" will be triggered when changing bond's active slave. [ 101.055189] BUG: scheduling while atomic: bash/902/0x00000200 [ 101.055726] Modules linked in: [ 101.058211] CPU: 3 PID: 902 Comm: bash Not tainted 6.9.0-rc4+ #1 [ 101.058760] Hardware name: [ 101.059434] Call Trace: [ 101.059436] <TASK> [ 101.060873] dump_stack_lvl+0x51/0x60 [ 101.061275] __schedule_bug+0x4e/0x60 [ 101.061682] __schedule+0x612/0x7c0 [ 101.062078] ? __mod_timer+0x25c/0x370 [ 101.062486] schedule+0x25/0xd0 [ 101.062845] schedule_timeout+0x77/0xf0 [ 101.063265] ? asm_common_interrupt+0x22/0x40 [ 101.063724] ? __bpf_trace_itimer_state+0x10/0x10 [ 101.064215] __wait_for_common+0x87/0x190 [ 101.064648] ? usleep_range_state+0x90/0x90 [ 101.065091] cmd_exec+0x437/0xb20 [mlx5_core] [ 101.065569] mlx5_cmd_do+0x1e/0x40 [mlx5_core] [ 101.066051] mlx5_cmd_exec+0x18/0x30 [mlx5_core] [ 101.066552] mlx5_crypto_create_dek_key+0xea/0x120 [mlx5_core] [ 101.067163] ? bonding_sysfs_store_option+0x4d/0x80 [bonding] [ 101.067738] ? kmalloc_trace+0x4d/0x350 [ 101.068156] mlx5_ipsec_create_sa_ctx+0x33/0x100 [mlx5_core] [ 101.068747] mlx5e_xfrm_add_state+0x47b/0xaa0 [mlx5_core] [ 101.069312] bond_change_active_slave+0x392/0x900 [bonding] [ 101.069868] bond_option_active_slave_set+0x1c2/0x240 [bonding] [ 101.070454] __bond_opt_set+0xa6/0x430 [bonding] [ 101.070935] __bond_opt_set_notify+0x2f/0x90 [bonding] [ 101.071453] bond_opt_tryset_rtnl+0x72/0xb0 [bonding] [ 101.071965] bonding_sysfs_store_option+0x4d/0x80 [bonding] [ 101.072567] kernfs_fop_write_iter+0x10c/0x1a0 [ 101.073033] vfs_write+0x2d8/0x400 [ 101.073416] ? alloc_fd+0x48/0x180 [ 101.073798] ksys_write+0x5f/0xe0 [ 101.074175] do_syscall_64+0x52/0x110 [ 101.074576] entry_SYSCALL_64_after_hwframe+0x4b/0x53 As bond_ipsec_add_sa_all and bond_ipsec_del_sa_all are only called from bond_change_active_slave, which requires holding the RTNL lock. And bond_ipsec_add_sa and bond_ipsec_del_sa are xfrm state xdo_dev_state_add and xdo_dev_state_delete APIs, which are in user context. So ipsec_lock doesn't have to be spin lock, change it to mutex, and thus the above issue can be resolved.

In the Linux kernel, the following vulnerability has been resolved: can: mcp251x: fix deadlock if an interrupt occurs during mcp251x_open The mcp251x_hw_wake() function is called with the mpc_lock mutex held and disables the interrupt handler so that no interrupts can be processed while waking the device. If an interrupt has already occurred then waiting for the interrupt handler to complete will deadlock because it will be trying to acquire the same mutex. CPU0 CPU1 ---- ---- mcp251x_open() mutex_lock(&priv->mcp_lock) request_threaded_irq() <interrupt> mcp251x_can_ist() mutex_lock(&priv->mcp_lock) mcp251x_hw_wake() disable_irq() <-- deadlock Use disable_irq_nosync() instead because the interrupt handler does everything while holding the mutex so it doesn't matter if it's still running.

In the Linux kernel, the following vulnerability has been resolved: net, neigh: Do not trigger immediate probes on NUD_FAILED from neigh_managed_work syzkaller was able to trigger a deadlock for NTF_MANAGED entries [0]: kworker/0:16/14617 is trying to acquire lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 [...] but task is already holding lock: ffffffff8d4dd370 (&tbl->lock){++-.}-{2:2}, at: neigh_managed_work+0x35/0x250 net/core/neighbour.c:1572 The neighbor entry turned to NUD_FAILED state, where __neigh_event_send() triggered an immediate probe as per commit cd28ca0a3dd1 ("neigh: reduce arp latency") via neigh_probe() given table lock was held. One option to fix this situation is to defer the neigh_probe() back to the neigh_timer_handler() similarly as pre cd28ca0a3dd1. For the case of NTF_MANAGED, this deferral is acceptable given this only happens on actual failure state and regular / expected state is NUD_VALID with the entry already present. The fix adds a parameter to __neigh_event_send() in order to communicate whether immediate probe is allowed or disallowed. Existing call-sites of neigh_event_send() default as-is to immediate probe. However, the neigh_managed_work() disables it via use of neigh_event_send_probe(). [0] <TASK> __dump_stack lib/dump_stack.c:88 [inline] dump_stack_lvl+0xcd/0x134 lib/dump_stack.c:106 print_deadlock_bug kernel/locking/lockdep.c:2956 [inline] check_deadlock kernel/locking/lockdep.c:2999 [inline] validate_chain kernel/locking/lockdep.c:3788 [inline] __lock_acquire.cold+0x149/0x3ab kernel/locking/lockdep.c:5027 lock_acquire kernel/locking/lockdep.c:5639 [inline] lock_acquire+0x1ab/0x510 kernel/locking/lockdep.c:5604 __raw_write_lock_bh include/linux/rwlock_api_smp.h:202 [inline] _raw_write_lock_bh+0x2f/0x40 kernel/locking/spinlock.c:334 ___neigh_create+0x9e1/0x2990 net/core/neighbour.c:652 ip6_finish_output2+0x1070/0x14f0 net/ipv6/ip6_output.c:123 __ip6_finish_output net/ipv6/ip6_output.c:191 [inline] __ip6_finish_output+0x61e/0xe90 net/ipv6/ip6_output.c:170 ip6_finish_output+0x32/0x200 net/ipv6/ip6_output.c:201 NF_HOOK_COND include/linux/netfilter.h:296 [inline] ip6_output+0x1e4/0x530 net/ipv6/ip6_output.c:224 dst_output include/net/dst.h:451 [inline] NF_HOOK include/linux/netfilter.h:307 [inline] ndisc_send_skb+0xa99/0x17f0 net/ipv6/ndisc.c:508 ndisc_send_ns+0x3a9/0x840 net/ipv6/ndisc.c:650 ndisc_solicit+0x2cd/0x4f0 net/ipv6/ndisc.c:742 neigh_probe+0xc2/0x110 net/core/neighbour.c:1040 __neigh_event_send+0x37d/0x1570 net/core/neighbour.c:1201 neigh_event_send include/net/neighbour.h:470 [inline] neigh_managed_work+0x162/0x250 net/core/neighbour.c:1574 process_one_work+0x9ac/0x1650 kernel/workqueue.c:2307 worker_thread+0x657/0x1110 kernel/workqueue.c:2454 kthread+0x2e9/0x3a0 kernel/kthread.c:377 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:295 </TASK>

In the Linux kernel, the following vulnerability has been resolved: net: hns3: fix a deadlock problem when config TC during resetting When config TC during the reset process, may cause a deadlock, the flow is as below: pf reset start │ ▼ ...... setup tc │ │ ▼ ▼ DOWN: napi_disable() napi_disable()(skip) │ │ │ ▼ ▼ ...... ...... │ │ ▼ │ napi_enable() │ ▼ UINIT: netif_napi_del() │ ▼ ...... │ ▼ INIT: netif_napi_add() │ ▼ ...... global reset start │ │ ▼ ▼ UP: napi_enable()(skip) ...... │ │ ▼ ▼ ...... napi_disable() In reset process, the driver will DOWN the port and then UINIT, in this case, the setup tc process will UP the port before UINIT, so cause the problem. Adds a DOWN process in UINIT to fix it.

A flaw was found in libvirt. The virStoragePoolObjListSearch function does not return a locked pool as expected, resulting in a race condition and denial of service when attempting to lock the same object from another thread. This issue could allow clients connecting to the read-only socket to crash the libvirt daemon.

A vulnerability identified in NetIQ Advance Authentication that doesn't enforce account lockout when brute force attack is performed on API based login. This issue may lead to user account compromise if successful or may impact server performance. This issue impacts all NetIQ Advance Authentication before 6.3.5.1

In the Linux kernel, the following vulnerability has been resolved: firmware: qcom: scm: Mark get_wq_ctx() as atomic call Currently get_wq_ctx() is wrongly configured as a standard call. When two SMC calls are in sleep and one SMC wakes up, it calls get_wq_ctx() to resume the corresponding sleeping thread. But if get_wq_ctx() is interrupted, goes to sleep and another SMC call is waiting to be allocated a waitq context, it leads to a deadlock. To avoid this get_wq_ctx() must be an atomic call and can't be a standard SMC call. Hence mark get_wq_ctx() as a fast call.

In the Linux kernel, the following vulnerability has been resolved: net/mlx5e: Take state lock during tx timeout reporter mlx5e_safe_reopen_channels() requires the state lock taken. The referenced changed in the Fixes tag removed the lock to fix another issue. This patch adds it back but at a later point (when calling mlx5e_safe_reopen_channels()) to avoid the deadlock referenced in the Fixes tag.

In the Linux kernel, the following vulnerability has been resolved: mm/hugetlb: fix hugetlb vs. core-mm PT locking We recently made GUP's common page table walking code to also walk hugetlb VMAs without most hugetlb special-casing, preparing for the future of having less hugetlb-specific page table walking code in the codebase. Turns out that we missed one page table locking detail: page table locking for hugetlb folios that are not mapped using a single PMD/PUD. Assume we have hugetlb folio that spans multiple PTEs (e.g., 64 KiB hugetlb folios on arm64 with 4 KiB base page size). GUP, as it walks the page tables, will perform a pte_offset_map_lock() to grab the PTE table lock. However, hugetlb that concurrently modifies these page tables would actually grab the mm->page_table_lock: with USE_SPLIT_PTE_PTLOCKS, the locks would differ. Something similar can happen right now with hugetlb folios that span multiple PMDs when USE_SPLIT_PMD_PTLOCKS. This issue can be reproduced [1], for example triggering: [ 3105.936100] ------------[ cut here ]------------ [ 3105.939323] WARNING: CPU: 31 PID: 2732 at mm/gup.c:142 try_grab_folio+0x11c/0x188 [ 3105.944634] Modules linked in: [...] [ 3105.974841] CPU: 31 PID: 2732 Comm: reproducer Not tainted 6.10.0-64.eln141.aarch64 #1 [ 3105.980406] Hardware name: QEMU KVM Virtual Machine, BIOS edk2-20240524-4.fc40 05/24/2024 [ 3105.986185] pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--) [ 3105.991108] pc : try_grab_folio+0x11c/0x188 [ 3105.994013] lr : follow_page_pte+0xd8/0x430 [ 3105.996986] sp : ffff80008eafb8f0 [ 3105.999346] x29: ffff80008eafb900 x28: ffffffe8d481f380 x27: 00f80001207cff43 [ 3106.004414] x26: 0000000000000001 x25: 0000000000000000 x24: ffff80008eafba48 [ 3106.009520] x23: 0000ffff9372f000 x22: ffff7a54459e2000 x21: ffff7a546c1aa978 [ 3106.014529] x20: ffffffe8d481f3c0 x19: 0000000000610041 x18: 0000000000000001 [ 3106.019506] x17: 0000000000000001 x16: ffffffffffffffff x15: 0000000000000000 [ 3106.024494] x14: ffffb85477fdfe08 x13: 0000ffff9372ffff x12: 0000000000000000 [ 3106.029469] x11: 1fffef4a88a96be1 x10: ffff7a54454b5f0c x9 : ffffb854771b12f0 [ 3106.034324] x8 : 0008000000000000 x7 : ffff7a546c1aa980 x6 : 0008000000000080 [ 3106.038902] x5 : 00000000001207cf x4 : 0000ffff9372f000 x3 : ffffffe8d481f000 [ 3106.043420] x2 : 0000000000610041 x1 : 0000000000000001 x0 : 0000000000000000 [ 3106.047957] Call trace: [ 3106.049522] try_grab_folio+0x11c/0x188 [ 3106.051996] follow_pmd_mask.constprop.0.isra.0+0x150/0x2e0 [ 3106.055527] follow_page_mask+0x1a0/0x2b8 [ 3106.058118] __get_user_pages+0xf0/0x348 [ 3106.060647] faultin_page_range+0xb0/0x360 [ 3106.063651] do_madvise+0x340/0x598 Let's make huge_pte_lockptr() effectively use the same PT locks as any core-mm page table walker would. Add ptep_lockptr() to obtain the PTE page table lock using a pte pointer -- unfortunately we cannot convert pte_lockptr() because virt_to_page() doesn't work with kmap'ed page tables we can have with CONFIG_HIGHPTE. Handle CONFIG_PGTABLE_LEVELS correctly by checking in reverse order, such that when e.g., CONFIG_PGTABLE_LEVELS==2 with PGDIR_SIZE==P4D_SIZE==PUD_SIZE==PMD_SIZE will work as expected. Document why that works. There is one ugly case: powerpc 8xx, whereby we have an 8 MiB hugetlb folio being mapped using two PTE page tables. While hugetlb wants to take the PMD table lock, core-mm would grab the PTE table lock of one of both PTE page tables. In such corner cases, we have to make sure that both locks match, which is (fortunately!) currently guaranteed for 8xx as it does not support SMP and consequently doesn't use split PT locks. [1] https://lore.kernel.org/all/1bbfcc7f-f222-45a5-ac44-c5a1381c596d@redhat.com/

In the Linux kernel, the following vulnerability has been resolved: i2c: tegra: Do not mark ACPI devices as irq safe On ACPI machines, the tegra i2c module encounters an issue due to a mutex being called inside a spinlock. This leads to the following bug: BUG: sleeping function called from invalid context at kernel/locking/mutex.c:585 ... Call trace: __might_sleep __mutex_lock_common mutex_lock_nested acpi_subsys_runtime_resume rpm_resume tegra_i2c_xfer The problem arises because during __pm_runtime_resume(), the spinlock &dev->power.lock is acquired before rpm_resume() is called. Later, rpm_resume() invokes acpi_subsys_runtime_resume(), which relies on mutexes, triggering the error. To address this issue, devices on ACPI are now marked as not IRQ-safe, considering the dependency of acpi_subsys_runtime_resume() on mutexes.

Vulnerabilities (CVE)